Tip 1: How to install a hot tub

Recently, the demand for the bath-tub is growing.This is understandable.Whirlpool has a healing effect on the mind, strengthens the immune system and helps to get rid of a number of different diseases.Works related to the installation of hydromassage equipment require professional knowledge and skills, so the connection is best left to professionals bathroom.But if you are confident in their abilities, and you have experience with electrical and plumbing, you can try to install a hot tub own.
Guide
1
Remove razmeryPered while necessary to go to the store for a new bathroom, you should carefully measure the dimensions of the room in which you plan to install it.Size of the bathroom must be a minimum of one meter larger than the chosen model.The recommended ceiling height in the room - not less than 3 m. It is worth remembering that because of the large weight of the spa its installation can be done only in the houses with concrete floors.Note the location of plumbing pipes.If you are installi
ng a hot bath tube must not rest against the ribs jacuzzi and interfere with the normal operation of equipment.It is desirable that the opening of the pipe sewage sludge took the floor.If this is not possible - make sure that the hole is located at a height of no more than 3 cm from the floor.Otherwise Installation must be carried out on the podium.
2
Prepare pomeschenieDemontiruyte old bath .Before installing the new hot tub is recommended for replacement of sewer and water pipes.If necessary, level the floor and do the waterproofing.It should be remembered that the hot equipment requires the installation of a strictly horizontal.
3
Carefully read the instructions that came with the equipment.
4
Set frame bathroom and put it horizontally with special adjustable feet included in the kit and building level.If necessary, install additional supports.Installation should be performed in such a way that access to the connecting hose, attachments, siphons and other parts baths remained free.
5
Connect bath to the sewerage system via water seal, supplied.Fit the mixer with water pipes.
6
Connect electrical equipment.We recommend connecting bath directly to the distribution box with the help of a three-phase wires with double insulation.If this is not possible - make sure that your outlet has a ground connection.
7
Check all seams and joints bath for leaks.

Tip 2: How to install a hot tub

Installation and operation of hot tubs has a number of nuances that must be known.If you do it right, your tub will last a long time, and problems with it then you will not have any.
How to install a hot tub
Guide
1
Room Dimensions
minimum size of the room where you plan to install a hot tub, is the size of the bath plus 1 m on each side.This increase will allow you to have free access to the space under the bath (in the case of cleaning).There are overlaps requirement - they must be panel, made of reinforced concrete.Do not forget doorways - a bath must pass through them safely.
2

Sewerage Pumping water from the bathroom made using standard pipe diameter of 50 mm PVC.It is better if the drain hole is arranged in the corner.Out sewer pipe may be run from the wall, if the distance between the floor and the lowest point is equal to 5 cm high.
3

water quality is mandatory to have to install a mechanical filter water strainer.However, it is also desirable to install a fine filter.Sometimes, if the water is too hard and contains a lot of iron, it is necessary to establish also a special unit that softens the water and removes it from the iron.
4
Electrical connection
for placement in the bathroom outlet hot tub can not be connected.And it usually is connected to a distribution box brownie, whole cable.Obligatory is the installation of the emergency shutdown, as well as a separate circuit breaker.To connect, use a copper cable with three conductors (phase conductor and shield wire zero) and double insulation of PVC.Equipment hot tubs consumes about 1.9-3.5 kW of electricity.It turns out that the section of each core of the cable must be 1.5-3 mm 2.
5
ventilation and leveling
hot tubs are installed horizontally, on a level.The slightest deviation would be fraught with unpleasant consequences.Produce leveling bath using the screw feet variable height, which tub, and worth it.
6
Sides bathroom closed ornamental or decorative wall panels, tiled.In the first case between the floor panel and the need to leave a small gap (1.5-3 cm).This is to ensure heat dissipation and ventilation equipment - a fan, a pump, a control unit, which is located under the cup.In the second case, the wall should be two small ventilation hatch.Part of the wall make removable, so you can get to the equipment for its prevention and repair or sweep out of the bath waste.
995
0
1
Plumbing