Tip 1: How to restore the bath

Over time, the enamel bath cracks, gets a yellow tint, hard water an unpleasant rusty stains.Complete replacement of the bath, of course, can remedy this situation, but requires not only moving heavy plumbing and reconnect communications, replacing tiling walls and floors.If you are not yet ready to fully repair the bathroom, just try to restore an old tub .
you need
  • - acrylic insert;
  • - cleaning powder;
  • - abrasive stone;
  • - white spirit or petrol;
  • - enamel;
  • - paint sprayer or brush;
  • - liquid acrylic.
Guide
1
Perform external examination of the bath, if the housing is cracked or deformed, on-site drainage visible chips - the usual recovery enamel does not help, more effective measures are needed.For example, try to pick up the finished acrylic liner in the hardware store.If you do it, install it according to the instructions inside your bath and enjoy the new look of the room.
2
To fix small cracks and rough places on the enamel chips, a brownish tint - try to restore the ena
mel.If you can not hire a specialist, cover enamel bath on their own.
3
On the surface, apply a cleaning powder that does not contain chlorine, and strip her abrasive stone enshrined in the drill or grinder.The surface should be smooth and uniform, free from voids and depressions.Always use gloves and a respirator as fine dust and debris may fly too far.
4
Big Sweep crumbs, dust cleaner, rinse bath water.Clean the surface from rust and degrease it, for example, white spirit or petrol.Enter full bath of hot water, wait a few minutes and drain the water.Wait until completely dry.
5
Prepare enamel, mixing and curing the liquid portion in strict accordance with the instructions on the can.Apply a base coat of enamel using a brush or spray gun on the surface of the bath.Of course, when you use the nebulizer you will get better results.
6
Wait drying the surface and apply another coat of enamel to equalize.Do not allow dust and debris at the time of painting, or coating will be spoiled.Take care to avoid bubbles and streaks.

Tip 2: How to restore the bathroom

Over time bath loses any good looks, and shows the damage, cracks, chips, and various defects.The consumer is faced with the dilemma - to buy a new bathroom or renovate the old one?The second option is more advantageous, because it allows to solve the problem for less money.
How to restore the bathroom
you need
  • 1st way:
  • - enamel;
  • - Cleaners;
  • - waterproof sandpaper or an abrasive stone;
  • - brush, spray, inker.
  • Method 2:
  • - acrylic insert;
  • - mounting adhesive.
Guide
1
Refresh old bath can, covering it with enamel or acrylic insert mounted.Enamelling baths you can implement on their own or with the help of specialists.
2
Clean the surface of the old enamel bath: apply with a brush or sponge powder without chlorine-containing composition (such as "Pemolyuks") and walk straight on powder waterproof sandpaper or an abrasive stone.Then rinse abrasion crumb and soap film water, strip rust and carefully degrease the surface of the bath.
3
Fill the tub with hot water for 5-10 minutes, drain the water and wipe dry with a lint-free cloth product.Prepare a working composition - Mix enamel and hardener.Apply the first coat of enamel - primer.Allow to dry colored bath for 10-15 minutes and apply a second coat of enamel.That's all.The whole process will take 3 - 4 hours.
4
Be careful with the paint brush bath, take care that there was no capacity to stains and bubbles.Otherwise the enamel flaked off immediately after dry.Normally tub dries 48 hours (in the instructions to the enamel indicate the time it dries, and the period after which the bath can be operated).Recommend for effect not to use the bathroom for another 5-7 days.
5
Some enamel is not applied with a brush or roller, and spray.This allows for a more uniform coating.However, the painting bath is strictly stick to the instructions and recommendations cover the newspapers or some old blanket the walls and the floor near the painted object to a thin layer of enamel is not turned on them.
6
second method restoration of the bath - acrylic liner.It is mounted on the individual order of any shape and color.Ready liner insert into an old bath, Dock drains and "interlock" with a special adhesive bath.Installation acrylic liner takes about 2 hours (it is better to trust the professionals).Service life is - 20 years.
Note
Otemalirovannuyu bath prohibited washed scouring powder such as "Comet" and "Pemolyuks" and apply products containing acid.It is advisable to clean the bath conventional washing powders or facilities for washing dishes.In the restored bath can be soaked underwear, but without bleach.
Sources:
  • How to restore the bath?
Helpful Hint
If you want to make the perfect plating bath, cover it with liquid acrylic.It is not necessary to perform this type of restoration on their own as great a risk to spoil the final bath.Invite Professionals and watch as they flooded along the sides of the liquid acrylic (stakril), it will fill all chipped and cracked, bath will get perfectly smooth look.After a few days you get a smooth acrylic liner that is perfect for your bath.
Sources:
  • how to restore the plastic tub
619
0
1
Plumbing