Tip 1: How to Put the batteries in the apartment

Properly selected and placed batteries provide not only the most out of the heat, but also prevent the penetration of cold air into the apartment.Therefore, when selecting and installing should follow certain rules.
Guide
1
Place battery under the windows, radiators when installing this rule is essential.Installed under the window curtain battery creates heat - a stream of warm air, which prevents the penetration of cold.Without it, the air in the apartment be quickly cooled at the window glass and fall down.
2
length radiator must be such as to cover the maximum width of the window.To heating was not excessive, the radiators are installed contemplate adjusting valves or thermostats.The presence of cranes and useful in the repair of the radiator - you will not have to cover the water in the riser, simply close the taps.
3
When calculating the number of radiators in the room, consider the material of the walls and the heat flow one section used battery (data has its parameter
s).For heating one square meter of an apartment in the panel house requires approximately 0.04 kW.If the walls are brick, on one square meter requires about 0.03 kW.Based on these data and the size of rooms, calculate the required number of sections of the radiator.
4
to the radiator did not give some of the heat located behind it the wall, insulate it and cover with foil.Thermal barrier coatings will prevent heating of the wall, and foil - reflect heat rays into the room.The distance between the radiator and the thermal insulation should be at least 3-4 cm. If you do not want to install the insulation, at least to cover the wall with foil.
5
to ensure proper air circulation install the radiator so that between it and the floor was a distance not less than 10 cm., And between the upper edge battery and sill - not less than 8 cm.
6
changing the radiators in the apartment , be sure to observe them withstood the load.The MDU pressure surges can greatly exceed the value of 16 atmospheres limit for aluminum radiators.If you live in a high-rise building, put bimetallic radiators (aluminum on a steel frame), they can withstand pressures up to 40 atmospheres.

Tip 2: How to install heating in the apartment

In recent rejection of the central heating is gradually becoming the norm, and not only in private homes, but also in high-rise apartments.By installing individual heating , you get the full independence of the often unstable working (often as a result of ongoing emergency operations) central heating systems, especially in winter, when the need for heating homes is highest.
How to install heating in the apartment
Guide
1
Before installation, the local autonomous heating in his apartment Agree dismantling and assembly work and get permission to conduct the local utilities.
2
After receiving permission from the Utilities After the completion of the heating season, and conducting maintenance work, proceed to the dismantling operations for removing old pipes, starting from the riser and old radiators.
3
Then enjoy a boiler installation, which already begin to layout a new heating system.Determine the number of newly installed heat sinks and in terms of their installation, as well as decide how complex will be a new heating system, are you going to do, for example, underfloor heating.Install the radiator is not difficult.Make sure only in the presence of the gun and you have the necessary hardware is usually included with the radiator.
4
If you do decide to install underfloor heating, make the dismantling of the flooring, lay the underfloor heating and fill them with a layer of screed.
5
sure to pre-calculate how many meters of pipe and other materials will be necessary for the installation of the entire heating system, draw a diagram of the pre-heating a sheet of paper listing all measurements.For ease of installation and soldering using plastic pipes, as they are more durable, reliable and easy to solder yourself.It is only necessary to have a special soldering iron.
6
According to the plan, drawn on paper, begin to plant heating system.The angular transition areas cut off sections of the route and then attach them to each other using reducers.
7
Fully paving heating , connect the previously purchased the boiler (gas or electric), battery (preferably cast iron or steel), and heated floors.Once again, visual double-check all joints for leaks.Perform a test run of the boiler and the entire heating system completely.
131
0
1
Plumbing