Tip 1: How to disassemble Ardo Washing machine

modern washing machine - a complex technical device and try to repair it yourself - a very risky activity.Any serious damage to the machine involves a challenge to master a professional from the service center.But if you are confident in their abilities, or whatever reason, do not have the ability to cause a wizard, you can try to disassemble the machine and self-diagnose and eliminate breakage.
you need
  • flat and cruciform screwdrivers, wrenches and 19 8/9, wire cutters, pliers, long bent pliers kleschidlya cleat clamps, service hook, crowbar
Guide
1
Remove the screws that secure the top panel of the machine is attached to the casing.
2
Lift the rear of the panel and slide the panel toward the rear of the machine.The panel should be disconnected from the housing.
3
Remove the top panel.
4
Remove the detergent dispenser.
5
cruciate screwdriver Remove the screws that secure the distributor box is attached to the front panel.
6
Slide the left side of the
control panel to 90 degrees, while holding it to the right hand.Make sure the panel is unhooked from the mounting fixture.
7
Take service hook.Insert it into the longer end opening of the drawer, and the other end secured to a side wall of the washing machine.Hang on a panel, turning it 180 degrees.
8
Remove the screws with which the service panel is attached to the side walls of the machine.
9
Carefully separate service panel using crowbar.
10
Open the washing machine door.
11
Remove the front access door of the clamp, using a flathead screwdriver.
12
Unhook the cuff on the front of the machine.
13
Remove the screws that hold the front and side of the machine, using the cross-shaped screwdriver.
14
Remove the front panel of the machine.
15
Loosen the clamp on the hose from the EGR valve to the tank, with the help of pliers.After that, remove the hose from the distributor.
16
Remove the clamp.
17
Loosen the clamp on the hose from the cylinder pressure switch
18
Disconnect the hose from the pressure switch and remove it from the sleeve of the appliance door.
19
Loosen the cuff on the tank, using a Phillips screwdriver.
20
Remove the tank collar cuff.
21
Unhook the collar on the access door and remove it from the washing machine drum.
Your washing machine is disassembled.

Tip 2: How to disassemble washing machine

With self-repair automatic washing machines, be aware that the order of their disassembly depends on the make and model of the unit.To determine the sequence of actions you need to take a sample of any particular washing machine.For example, a car with a vertical load of laundry.
How to disassemble washing machine
you need
  • - flat screwdriver;
  • - pliers;
  • - wrench
Guide
1
Remove the four mounting bolts on the rear of the machine and remove the side panels.
2
Set the temperature control knob and switch between the original position.Remove the locking bolt on the control panel.Gently push the latch cover decorative front panel, using a flathead screwdriver.Lift and remove the cover.
3
Unscrew the two screws located on the sides of the front panel.Tighten using pliers and drown the latch, which is attached to the cable harness.Release the retaining clips with a flat screwdriver and remove the front panel of the washing machine.
4
Press the plastic clips of the detergent drawer and pull it out of the car.
5
Peel back the rubber seal, unscrew the screws and remove the tank cover it.Remove the spring ring using a flat screwdriver and remove the seal.Remove the plug door hinges, using a flathead screwdriver.Remove the door.
6
Remove pull cord out of the socket, remove the four screws on the lid of the tank.Click on the tabs at the rear of the machine, and a little lift up the cover.Remove the 2 tubes that are to the right and fold the lid of the tank.
7
Turn off fixing bolts tank top and screw on the left cross support.
8
Remove the V-belt pulley.Remove the locking bolt and remove the drum pulley.
9
Remove the upper bolts right cross.Lift the upper part of the tank using a screwdriver.Repeat on the left side.
Remove the upper part of the tank.
10
Unscrew the bolts reinforcement straps, paying attention to their labeling.Roman numerals indicate the order of tightening bolts.Unscrew the fastening bolts at the sides and under the cross bar carrying two sides of the washing machine.Remove the bearing of the cross.
11
Remove the seal from the slot.Press the plastic clips located on the tanks of the tank and remove the drum.
12
remove the filter.Remove the cover from the hydrostatic drive a screwdriver.Remove the terminal from the heating element and unscrew the locking screw with a wrench.Remove the heating element.
13
Remove the plugs for the motor, remove the screws fixed to the chassis and remove the electric motor.
14
Disconnect the electrical terminals of the drain pump, remove the bolts and remove the pump.
15
Remove the valve for water tank by removing the terminals and protective kyshku.
Your washing machine is completely dismantled.
Sources:
  • «Modern washing machines," A.Rodin, NATyunin Solon-Press, 2007
  • how to disassemble a vertical washing machine
Note
Before you dismantle the washing machine do not forget to unplug it from the mains, sewerage and water supply.

to remove the colored service panels are used only wooden or plastic crowbar.
Helpful Hint
Each model of the washing machine has its own design features and, as a result, differences in the disassembly procedure.
Sources:
  • disassembly of the washing machine ardo
867
0
1
Plumbing